Aggregating rebar quantities by size and the measurement boundaries: grouping by bar type / diameter band / member; hooks, design laps and anchorage included; construction laps and measures bars not measured; mechanical couplers counted as units without laps; in t to three decimal places
Rebar quantity W(t) = Sum(ni x Li x wi) / 1000, with lengths taken as the centre-line lengths of the bars shown on the design drawings (GB/T 50860-2024 Annex A.15.6), aggregated at three levels: bar type / grade, diameter band (quota manuals commonly d10 and below / above d10) and member location (cast-in-place, rebar cages, secondary structure, sundry members, mesh). Included in the BOQ quantity: anchorage bars projecting from members as designed (GB/T 50854-2024 Annex E note 10) and laps marked in the design or required by the code (lap length ll corrected for the splice-area percentage and no less than 300mm, GB 50010-2010 Clause 8.4.4). Excluded: construction laps such as stock-length laps, non-designed chair bars, diagonal brace bars, anti-floating bars and spacers, and non-designed post-installed bars; rebar at post-cast strips is not itemised separately. Where the drawings require mechanical connection, the straight-thread sleeve coupler item applies and no lap quantity is calculated; couplers are counted as units by the number shown on the design. Rounding of totals: quantities in t are stated to three decimal places, the fourth being rounded (GB/T 50861-2024 Clause 3.0.3).
Applicable Codes
- GB/T 50854-2024 App. E 混凝土及钢筋混凝土工程 钢筋项目说明第1~13条
- GB/T 50860-2024 App. A.15.6(设计图示钢筋长度为中心线长度)、A.15.10(施工搭接不计算工程量)
- GB/T 50861-2024 第3.0.3条(工程计量有效位数)、App. B.9.3(高架桥工程钢筋规定)
- GB 50010-2010 第8.3.1条(锚固长度)、第8.4.4条(搭接长度)
- DB11/T 2382-2024 第7.1.32~7.1.34条(损耗与措施筋合计5%、12m/9m 搭接、直螺纹套筒接头按个)
- SJG 181.2-2024 第5.2.1条(钢筋制作安装与搭接兜底规则)
- 湖南 2025 版房屋建筑与装饰工程消耗量标准 钢筋工程量计算规则
Topic scope
How rebar quantities are aggregated from 'drawing length' to 'tonnage reported': the grouping rules, what counts (hooks, design laps, anchorage), how measures bars and mechanical couplers are treated, and the rounding of aggregated quantities. For the 2024 series of measurement standards covering buildings, municipal works and structures.
Core conclusions
1. Basic aggregation formula W(t) = Sum(ni x Li x wi) / 1000 ni - number of bars of the same size; Li - design length of one bar (m); wi - theoretical mass per metre of that size (kg/m, by nominal diameter). First aggregate the lengths by group, then multiply by the mass per metre, finally total and round.
2. Length basis 'The design length of a bar in the measurement rules means the centre-line length of the bar.' (GB/T 50860-2024 Annex A.15.6) Bent bars have other bases in some quota volumes (e.g. the Hunan 2025 consumption standard: by outside-face length, without deducting elongation) - a quota consumption basis that runs on a separate track from the BOQ quantity; the two must not be mixed.
3. Grouping principles (all three must hold before merging)
- Separate items by bar type / grade: 'For rebar works, distinguish the different bar types and sizes; multiply the design length by the unit mass and calculate in tonnes.'
- Group by diameter: quota line items commonly split 'within d10mm / beyond d10mm', some also d12 and d25 bands; apply by band within one material, not one band throughout.
- Code separately by member / location (GB/T 50854-2024 Annex E notes): rebar of cast-in-place members is coded under the member rebar items; rebar of general precast and assembled members is included in the member and not itemised separately; diaphragm walls and bored piles are itemised as 'rebar cages'; constructional columns, ring beams and lintels as 'cast-in-place secondary structure rebar'; rebar of cast-in-place wells and pools and of cable trenches and ditches as 'cast-in-place sundry member rebar'; fabricated rebar mesh and ready-made steel wire mesh as 'rebar mesh' and 'steel wire mesh'; prestressed bars, wire tendons and strands are itemised separately by material type and size. Practice: aggregate lengths at the three levels 'member -> grade -> diameter'; stirrups and straight bars are totalled separately (stirrup length includes hooks, on the centre line); when merging one size across members, keep the member detail for reconciliation; mechanical couplers are counted separately as units and not merged into the rebar mass.
4. Hooks 'Plain round bars shall have 180-degree hooks at their ends, the straight length after bending being no less than 3d; hooks may be omitted where the bar is used in compression.' (GB 50010-2010 Clause 8.3.1, note to Table 8.3.1) The hook add-on length enters the bar length on the centre line.
5. Laps
- Included: laps marked in the design (including those required by the code). The tied lap length of longitudinal tension bars is corrected for the percentage of lapped area within one lap zone: 'the lap length ... is calculated by the following formula and shall be no less than 300mm'; where the area percentage is an intermediate table value, the correction factor may be interpolated (GB 50010-2010 Clause 8.4.4).
- Excluded: 'apart from laps marked in the design (including those required by the code), other construction laps (such as stock-length laps) are not measured as quantities.' (GB/T 50854-2024 Annex E note 11; GB/T 50860-2024 Annex A.15.10; GB/T 50861-2024 Annex B.9.3)
- Quota fallback (where neither the drawings nor the code mark laps): 'rebar within d10mm: one lap per 12m of length; rebar beyond d10mm: one lap per 9m' (SJG 181.2-2024 Clause 5.2.1; DB11/T 2382-2024 Clause 7.1.33 to the same effect, adding that 'mechanically connected bars take no lap quantity').
6. Anchorage 'Anchorage bars projecting from each cast-in-place member take their length from the design and are merged into the rebar quantity of that member.' (GB/T 50854-2024 Annex E note 10; GB/T 50861-2024 Annex B.9.3 item 1) The anchorage length itself is computed under GB 50010-2010 Clause 8.3.1 (the basic anchorage length l_ab depends on fy, ft and d; the anchorage length l_a = zeta_a.l_ab, no less than 200mm, the product of the zeta_a factors no less than 0.6).
7. Measures bars, post-installed bars and wastage
- 'The rebar items do not measure the quantities of non-designed measures bars such as chair bars, diagonal brace bars, anti-floating bars and spacers.' (GB/T 50854-2024 Annex E note 12; GB/T 50861-2024 Annex B.9.3 item 2) But the 'work content' of every rebar item 'shall include the corresponding measures bars', their cost being spread into the all-in unit rate.
- 'Post-installed bars not required by the design are not itemised or measured separately. Where the design requires them, code them under the corresponding member rebar items and add a description of the embedding requirement.' (Annex E note 13)
- Rebar at post-cast strips is not itemised or measured separately; it is merged into the rebar quantity of the corresponding cast-in-place member (note 9).
- Wastage is a consumption matter and does not enter the BOQ quantity: DB11/T 2382-2024 Clause 7.1.32 - for rebar (pile cages excepted), the wastage, covering fabrication loss and the measures bars (chairs, supports, spacers), is suitably taken as 5%.
8. Mechanical connection versus tied laps 'Where the drawings require mechanical connection, the straight-thread sleeve coupler item applies, and no lap rebar quantity is calculated.' 'The quantity of straight-thread sleeve couplers is calculated by the number shown on the design drawings.' (DB11/T 2382-2024 Clauses 7.1.32 and 7.1.34) Local practice agrees: 'electro-slag welded, sleeve-pressed and straight-thread couplers of rebar are counted as units and priced under the corresponding items, with no lap length taken.' (Hunan 2025 consumption standard, rebar measurement rules) -> couplers are priced as units, the lap length is dropped, and the two are never counted together.
9. Rounding of totals 'When measuring the works, the significant figures of the total of each item shall comply with the following: 1. in t and km, retain three decimal places, rounding the fourth; 2. in m, m2, m3 and kg, retain two decimal places, rounding the third; 3. in units, pieces, bars, groups, machines, sets, places, blocks, stations, systems, items and the like, take integers.' (GB/T 50861-2024 Clause 3.0.3) So rebar is reported in t to three decimal places; keep more digits in the working calculations to avoid accumulated truncation error.
Applicable boundaries
- The BOQ bases above follow the 2024 series (GB/T 50854-2024, GB/T 50860-2024, GB/T 50861-2024) generally; railway, highway and water projects follow their own industry measurement rules and quota notes (e.g. railway adds lap quantity for bars not joined by couplers).
- The 12m/9m lap fallback applies only where neither the design nor the code marks laps; the details differ across local quota volumes - confirm against the volume in use.
- Hook add-on lengths and stirrup lengths (outside face or centre line) differ across quota volumes; BOQ and quota quantities run on separate tracks and must not be applied to each other.
- The significant-figure rule applies at the 'item total' stage, not to single-piece working calculations; the clause numbers on rounding differ between the measurement standards of different sectors.
Further reading
- GB/T 50854-2024, Standard for Measurement of Quantities of Work for Housing Construction and Decoration, Annex E (concrete and reinforced concrete works), rebar notes 1 to 13; GB/T 50860-2024 Annexes A.15.6 and A.15.10; GB/T 50861-2024 Clause 3.0.3 and Annex B.9.3 (rebar provisions for viaduct works).
- GB 50010-2010, Code for Design of Concrete Structures, Clause 8.3.1 (basic anchorage length l_ab, anchorage length l_a, and where the cover is no more than 5d, transverse bars of diameter no less than d/4 and the spacing requirements), Clause 8.4.4 (lap length l_l and the lap length correction factor zeta_l).
- DB11/T 2382-2024, Consumption Standard for Construction Works, Clauses 7.1.32 to 7.1.34 (wastage with measures bars at 5%, 12m/9m laps, straight-thread sleeve couplers by unit).
- SJG 181.2-2024, Municipal Consumption Standard, Volume 2 Bridge and Culvert Works, Clause 5.2.1; Hunan 2025 consumption standard for housing construction and finish works, 'rebar quantities are calculated as follows'.
Keywords
- 钢筋工程量计算
- 分规格汇总
- 钢筋直径分档
- 弯钩长度
- 搭接长度
- 锚固钢筋并入
- 直螺纹套筒接头
- 有效位数三位小数