Engineering Knowledge Cards.
Confidence HighUpdated 2026-08-11

Bridge pier-top swivel construction (horizontal/vertical rotation): code basis and key control parameter index

Core swivel control parameters: overturning stability factor > 1.5; after weighing and counterweighting, the rotation system must stand 24 h before trial rotation; angular velocity <= 0.02 rad/min, sudden pulling/stopping strictly forbidden; after seating, girder axis deviation <= 10 mm; before closure, cantilever-end relative elevation difference <= 1/100 of the closure-segment length and <= 15 mm, top elevation +/-20 mm; spherical hinge installation documented with imagery, supervision witnesses. Code index: TB 10303-2020 Sections 9.6/12.8, TB 10415-2018 Section 10.4, TB 10101-2018 Clauses 7.9.27~7.9.30, CJJ 2-2008 Section 16.8, CJJ/T 290-2019 Clause 13.6.4, DB11/T 1885-2021 Chapter 23, ZJQ08-SGJB 018-2018 Section 8.4.

Applicable Codes

  • TB 10303-2020 铁路桥涵工程施工安全技术规程
  • TB 10415-2018 铁路桥涵工程施工质量验收标准
  • TB 10101-2018 铁路工程测量规范
  • CJJ 2-2008 城市桥梁工程施工与质量验收规范
  • CJJ/T 290-2019 城市轨道交通桥梁工程施工及验收标准
  • DB11/T 1885-2021 桥梁工程施工安全技术规程
  • ZJQ08-SGJB 018-2018 桥梁工程施工技术标准

Topic Positioning

A standards index and key control parameters for pier-top swivel construction (a form of the horizontal-rotation method with the rotation system on the pier top), covering railway, urban bridge, urban rail, local, and enterprise standards.

Core Conclusions

Safety (TB 10303-2020 Section 9.6, DB11/T 1885-2021 Chapter 23, CJJ/T 290-2019 Clause 13.6.4): compile a dedicated method statement for high-risk works before swiveling; the rotation system's overturning stability factor > 1.5; before swiveling, weigh and counterweight per the measured unbalanced moment so the center-of-mass offset meets the design eccentricity; after the system is seated, stand 24 h without anomaly before the trial rotation; angular velocity no more than 0.02 rad/min, sudden pulls and stops strictly forbidden; hauling equipment sized at 2x the calculated hauling force with an over-rotation limit stop; perform a spatial collision check before swiveling. Acceptance (TB 10415-2018 Section 10.4, Table 10.4.20): after seating, girder axis deviation <= 10 mm; before closure, relative elevation difference of the two cantilever ends <= 1/100 of the closure-segment length and <= 15 mm; top elevation +/-20 mm; spherical hinge installation documented with imagery, with supervision witnessing hinge installation and the swivel. Surveying (TB 10101-2018 Clauses 7.9.27~7.9.30): total stations with nominal accuracy no less than 1", 1 mm + 1x10-6 D for horizontal, 0.3 mm/km digital levels for elevation; hinge-center positioning staking <= 1 mm, support feet <= 5 mm, reaction seats <= 10 mm; inching at 1 m from the design position, slowing at 0.5 m, coasting into position over the last 100 mm, with seated centerline deviation <= 20 mm. Arch vertical rotation (TB 10303-2020 Section 12.8): buckling and anchor cable safety factor > 2.0; stand off the supports 24 h, inspect, then rotate formally with staged loading.

Applicable Boundaries

Applies to the horizontal-rotation method (rigid-frame girder bridges, cable-stayed bridges, reinforced concrete and concrete-filled steel tube arch bridges) and vertical rotation of moderate-tonnage arch bridges; at the code level, all follow the "swivel construction" chapters — pier-top swivels have no separate provisions. The values listed are minimums; swivels over railways must also satisfy special conditions such as line blockages by the operator. Note in the highway system that JTG/T F50-2011 has been replaced by JTG/T 3650-2020.

Further Reading

Railway: TB 10303-2020 Section 9.6 (continuous-beam swivel safety checklist 9.6.5), Section 12.8 (arch vertical rotation); TB 10415-2018 Section 10.4 and Table 10.4.20; TB 10101-2018 Clauses 7.9.27~7.9.30. Urban: CJJ 2-2008 Section 16.8 (horizontal/vertical rotation principles and scope); CJJ/T 290-2019 Clause 13.6.4. Local/enterprise: DB11/T 1885-2021 Chapter 23; ZJQ08-SGJB 018-2018 Section 8.4 (full process flow and quality standard 8.4.6).

Keywords

  • 墩顶转体
  • 转体施工
  • 平转法
  • 竖转法
  • 转体桥
  • 抗倾覆稳定系数
  • 球铰
  • 转体就位允许偏差

Cited By