Engineering Knowledge Cards.
Confidence HighUpdated 2026-09-25

GB 51210-2016 vertical diagonal bracing provisions: working scaffolds (8.2.3) and support scaffolds (8.3.4) — width, inclination and spacing

Working scaffolds (GB 51210-2016 cl. 8.2.3): each vertical diagonal bracing band shall be 4-6 bays wide, not less than 6m and not more than 9m, diagonals at 45-60 degrees; below 24m height, one band at each end, corner and at intervals not over 15m, continuous from bottom to top; at 24m and above, continuous over the full outer face; cantilever and attached climbing scaffolds always continuous over the full outer face. Support scaffolds (cl. 8.3.4): spacing by safety grade — grade II every not more than 9m, grade I every not more than 6m (perimeter and interior, both directions); horizontal distance between diagonals preferably 6-9m, inclination 45-60 degrees.

Applicable Codes

  • GB 51210-2016 · Unified Standard for Safety Technology of Scaffolding in Building Construction 第 8.2.3 条
  • GB 51210-2016 · Unified Standard for Safety Technology of Scaffolding in Building Construction 第 8.3.4 条

Topic Positioning

This card consolidates the GB 51210-2016 provisions on vertical diagonal bracing: width, diagonal inclination and spacing for working scaffolds (cl. 8.2.3) and support scaffolds (cl. 8.3.4), plus the conversion principle for replacing large diagonal bracing with inclined struts/cross ties.

Core Conclusions

Vertical diagonal bracing differs for working and support scaffolds; the values must be executed separately.

I. Working scaffolds (cl. 8.2.3) — vertical diagonal bracing on the longitudinal outer face:

  1. Each bracing band shall be 4-6 bays wide, not less than 6m and not more than 9m; the angle of the diagonals to the horizontal shall be 45-60 degrees;
  2. Below 24m erection height: one band at each end, at corners and at intermediate intervals not exceeding 15m, continuous bottom to top; at 24m and above: continuous bottom to top over the full outer face;
  3. Cantilever scaffolds and attached climbing scaffolds: continuous bottom to top over the full outer face.

II. Support scaffolds (cl. 8.3.4):

  1. Safety grade II: one band around the perimeter and internally, longitudinally and transversally, at intervals not more than 9m;
  2. Safety grade I: ditto at intervals not more than 6m;
  3. Horizontal distance between vertical bracing diagonals preferably 6-9m; angle to the horizontal 45-60 degrees.

Substitution and supplementary rules (commentary):

  • Where inclined struts or cross ties replace large diagonal bracing on working scaffolds, set the interval by equal coverage area of the struts/ties and the large-bracing diagonals: below 24m, coverage may be 1/8-1/6 of the outer face; above 24m or where full large bracing is required, 1/4-1/3. Struts and ties run continuously bottom to top between adjacent poles vertically, repeating horizontally at bay intervals.
  • Horizontal interval when substituting: "below 24m, one set every 5-7 bays; above 24m, every 1-3 bays" — the upper line applies to taller erection heights and the lower line to shorter ones.
  • On support scaffolds the vertical bracing diagonals should converge at horizontal-tube levels; bracing, struts and ties are the main members ensuring overall stability, transferring horizontal loads and stiffening the frame; their density markedly affects capacity — with pole and lift spacing unchanged, densifying bracing significantly raises capacity.

Applicable Boundaries

  • Values apply to working and support scaffolds under GB 51210-2016; band width is governed jointly by "4-6 bays" and ">=6m, <=9m"; inclination uniformly 45-60 degrees.
  • Working scaffolds bracket spacing by the 24m height; cantilever and attached climbing scaffolds are always continuous over the full outer face regardless of height — the sub-24m spacing rules do not apply.
  • Support scaffolds set bracing spacing by safety grade (grade I <=6m, grade II <=9m), not by height.
  • Substituting struts/ties for large bracing must satisfy the coverage-area conversion — no arbitrary reduction; horizontal intervals take the upper line for taller, the lower line for shorter heights.
  • Not applicable: specialized systems such as railway scaffolds (separate standards); this card is detailing only, without capacity verification methods.

Further Reading

  • Original text: GB 51210-2016 cl. 8.2.3 (working-scaffold vertical bracing) and commentary, cl. 8.3.4 (support-scaffold vertical bracing) and commentary.
  • The same standard's base detailing: bottom (sweeping) tubes — a longitudinal sweeping tube is generally set 200mm above ground with the transverse one directly beneath, improving integrity and reducing the effective length of base poles.
  • Companion specialized codes for comparison: JGJ 130 (coupler steel-tube scaffolds) and JGJ 231 (ring-lock standards) refine bracing detailing.

Keywords

  • 竖向剪刀撑
  • 剪刀撑
  • 作业脚手架
  • 支撑脚手架
  • GB 51210
  • 建筑施工脚手架安全技术统一标准
  • 安全等级
  • 搭设高度24m

Cited By