Engineering Knowledge Cards.
Confidence HighUpdated 2026-10-25

Member boundary rules for measuring cast-in-place concrete columns, beams, slabs and walls: the levels to which column height and beam length run, the merge and split boundaries for slabs, the deduction thresholds for walls, the attribution of crossover nodes such as column caps, corbels, concealed beams and wall columns, and the differences among three parallel scopes - the BOQ measurement standard (GB/T 50854-2024), local consumption standards and traditional quota manuals

Cast-in-place concrete columns, beams, slabs and walls are all measured by volume (m3) on the dimensions shown on the design drawings, but the 'member boundaries' differ by governing scope. Building quota scope - with ribbed-slab (beam-and-slab) floors, column height runs from the top of the column base (or the top of the floor slab) to the top of the floor slab above; with beamless (flat-slab) floors, to the underside of the column cap; frame columns run to the column top; constructional columns run from the top of the member they root in to the underside of the member they anchor into, the wall-embedded toothing portions being merged into the column body. Beam length runs to the side face of columns; secondary beams run to the side face of primary beams; ribbed slabs take the sum of beam and slab volumes, beamless slabs take slab + column caps, plain slabs take the solid slab volume (this three-way split applies only to local consumption standards and traditional quota scopes). GB/T 50854-2024 Appendix E shows no merged 'ribbed / beamless / plain slab' items in its BOQ scope: slabs are itemised separately as solid floor slabs, sloped roof slabs, hollow floor slabs and other slabs, beams and slabs carry separate codes, and it expressly provides that 'where a wall meets a column, the wall is measured to the column face; where a wall meets a beam, the wall is measured to the beam underside; where a wall meets a slab, the slab is measured to the wall side'; special-shaped columns (section height-to-thickness ratio over 4 in every direction) are itemised as 'reinforced concrete walls'; walls deduct door and window openings and individual holes over 0.3m2, with wall pilasters and projections merged in. The rail-transit underground scope is the opposite: columns run to the underside of beams / slabs, beam-column overlaps go to the beam, and column caps merge into the column body.

Applicable Codes

  • GB/T 50854-2024 · Standard for measurement of building construction and fitting out works App. E(E.2.1、E.7.1~E.7.5)
  • GB/T 50861-2024 · Standard for Measurement of Quantities of Urban Rail Transit Works App. C.8.4
  • DB11/T 2382-2024 · Standard for Construction Consumption of Construction Works (Beijing) 第 4.6.4~4.6.6 条
  • TB/T 10831-2024 · Budget Quota of Railway Engineering (Volume 10: Housing Works) 册说明十
  • 江苏省建筑与装饰工程消耗量(2026 版)第五章混凝土及钢筋混凝土工程
  • 湖南省房屋建筑与装饰工程消耗量标准(2025 版)混凝土及钢筋混凝土工程

Topic positioning

This card answers how the 'member boundaries' are drawn for measuring cast-in-place concrete columns, beams, slabs and walls: to which face column height runs, to whose side face beam length runs, whether slabs and beams are measured merged, which openings walls deduct, and to which member the crossover nodes - column caps, corbels, concealed beams, wall columns - belong; it also gives the differences among the three parallel scopes (BOQ standard, local consumption standards, traditional quota manuals) and the red line that they must not be mixed.

Core conclusions

I. Fix the scope first: three parallel systems, no mixing

  • BOQ measurement (GB/T 50854-2024 Appendix E): cast-in-place concrete members follow the item setting of Table E.2.1, code 010502; the BOQ item setting, the content of item descriptions, the units of measurement and the measurement rules all follow that table. The slab items of Appendix E.7.4 are solid floor slabs, sloped roof slabs, hollow floor slabs, ramp slabs and other slabs - no merged 'ribbed slab / beamless slab / plain slab' items appear; E.7.5 states that 'balconies shall be coded and itemised separately as cast-in-place concrete beams, slabs and the like', i.e. beams and slabs carry separate codes and are not merged.
  • Local consumption standards (e.g. Beijing DB11/T 2382-2024 Clause 4.6.6; Jiangsu 2026 edition; Hunan 2025 edition): still carry 'ribbed slab / beamless slab / plain slab' items, ribbed slabs being measured merged.
  • Traditional quota manuals (TB/T 10831-2024 Volume 10, volume notes item 10): ribbed slabs comprise the primary and secondary beams and the slab, measured as the sum of the beam and slab volumes. => Where a BOQ is compiled under GB/T 50854-2024 and a merged 'ribbed slab' item is then applied, the scopes are mixed in error; anyone citing 'ribbed slabs at the sum of beam and slab volumes' must state that this is the quota scope.

II. Common deductions (identical across the scopes)

  • Cast-in-place reinforced concrete members make no deduction for the reinforcement, bolts, embedded inserts and stressing ducts within the member, but the volume of the structural steel in encased-steel skeletons is deducted (GB/T 50854-2024 Appendix E.7.1); Beijing standard 4.6.6 quantifies this: in steel-reinforced concrete frames, 0.127m3 of concrete is deducted per tonne of structural steel.
  • Walls and slabs make no deduction for individual holes no larger than 0.30m2 (holes over 0.30m2 are deducted); beams and columns make no deduction for reinforcement and embedded inserts.

III. Column height (four boundaries + special columns)

Beijing DB11/T 2382-2024 Clause 4.6.6 item 3, source wording:

  1. Column height: with ribbed-slab floors, from the top of the column base (or the top of the floor slab) to the top of the floor slab above; with beamless-slab floors, from the top of the column base (or the top of the floor slab) to the underside of the column cap; frame columns from the top of the column base to the column top; constructional columns from the top of the member they root in to the underside of the member they anchor into, the wall-embedded toothing portions (mayacha) being merged into the column body;
  2. corbels attached to a column are merged into the column volume;
  3. concrete-filled steel tube columns are measured by the sectional area within the tube times the tube height shown on the design drawings;
  4. raking columns by the column sectional area times the inclined centre-line length shown on the design drawings;
  5. core columns by the hole sectional area times the height shown on the design drawings.

TB/T 10831-2024 Volume 10, volume notes 10(4), same scope: ribbed-slab column height from the top of the column base (or floor slab top) to the top of the floor slab above; beamless slabs to the underside of the column cap; constructional columns over the full height with the wall-embedded portions merged into the column; corbels merged into the column.

Boundary clarification on 'storey-by-storey measurement of frame columns': the building-standard wording is 'measured from the top of the column base to the top of the column', i.e. measured to the top in one pass, with no layering rule at all. Splitting by storey (each storey from the top of its floor slab to the top of the slab above) is only a reconciliation device: the split interfaces sit at floor-slab tops, the split total must equal the one-pass figure, and the portion above the top-storey column must not be counted twice.

The rail-transit underground scope is the opposite (GB/T 50861-2024 Appendix C.8.4 item 1): 'Concrete columns: the column height is measured from the top of the column base (ground beams) (or the top of the floor slab) to the underside of the floor slab or beam above, and the parts where beams overlap columns are measured as beams. Corbels and column caps attached to columns are merged into the column volume.' - columns run to the beam underside / slab underside, beam-column overlaps go to the beam, column caps go to the column; this cannot be interchanged with the building rule of 'to the top of the floor slab above, caps to the slab (beamless slabs)', and the quantity difference is exactly the joint-zone volume.

IV. Beam length and beam depth

Beijing DB11/T 2382-2024 Clause 4.6.6 item 4, source wording:

  1. Beam length: where a beam meets a column, the beam length runs to the side face of the column; where a secondary beam meets a primary beam, the secondary beam length runs to the side face of the primary beam; where a beam meets a wall, the beam length runs to the side face of the wall; ring beams run on the centre line for external walls and on the net line for internal walls; lintels follow the dimensions shown on the design drawings;
  2. where a ring beam doubles as a lintel, the lintel volume is merged into the ring beam. Beam heads and beam pads built into walls are merged into the beam volume.

Supplementary scope (Jiangsu 2026 consumption standard): where a ring beam meets a constructional column, the beam length runs to the side face of the constructional column (excluding the toothing); where the lintel design is silent, take the opening width below the beam plus 250mm at each end; beam depth - where the beam top meets a slab, the beam depth runs to the slab top; where the beam mid or underside meets a slab, the slab thickness is not deducted. Rail-transit scope (GB/T 50861-2024 C.8.4-2): 'where a beam meets a column, the beam is measured through; beam heads built into walls are merged into the beam volume. Where a secondary beam meets a primary beam, the secondary beam length runs to the inner face of the primary beam. Beam depth runs from the beam underside to the slab underside; upstand beams from the slab top to the beam top.' BOQ E.7.4 further requires the slope to be described where the beam slope is no less than 20%.

V. Merge and split boundaries for slabs

  • Ribbed slabs (quota scope): ribbed slabs comprise the primary and secondary beams and the slab, measured as the sum of beam and slab volumes (TB/T 10831-2024 notes 10(7)1; Hunan 2025); Beijing is finer still: for ribbed slabs 'the slab area is measured on the net dimensions between primary beams', with secondary beams merged into the slab.
  • Beamless slabs: measured as the sum of the slab (edge beams included) and the column caps (TB/T 10831-2024; Hunan 2025); Beijing: beamless slabs on the horizontal projection of the slab outline, with column caps merged into the slab.
  • Plain slabs: on the solid slab volume / the net area between main walls; where a slab meets a ring beam it runs to the side face of the ring beam, and slab ends built into masonry walls are merged into the slab.
  • Shell slabs: the ribs and grade beams are merged into the shell. Hollow floor slabs: measured by volume on the dimensions shown on the design drawings, deducting the volume of the hollow parts; core-tube installation is measured by length on the design dimensions (Beijing); the Hunan scope measures the hollow tubes (boxes) on external volume, the cast hollow-floor volume being the slab volume less the module volume.
  • Cantilevered eaves, valleys and canopies: where cast-in-place eaves and valleys join a slab (roof or floor slabs), the external wall is the boundary; where they join a beam (ring beams included), the outer edge of the beam is the boundary; beyond the boundary they count as eaves and valleys; cantilevered slabs (plain slabs, canopies and the like) are measured by the volume projecting beyond the external wall, upstands being merged into the cantilevered slab.
  • 2024 BOQ scope (split items): roof slabs with slope under 20% are itemised as 'solid floor slabs', those no less than 20% as 'sloped roof slabs' with the slope described; concrete cast on steel plates is itemised as 'solid floor slabs', deducting the steel plate volume and accounting for the volume changes caused by the corrugations of the profiled sheet; hollow slabs take built-in tubes and boxes (glass-fibre reinforced composite tubes, stacked boxes, honeycomb cores and the like); eaves slabs, valley slabs, canopy slabs, projecting bay-window top (bottom) slabs, bay-window side panels, drop panels, balustrade panels and feature panels are coded separately as 'other slabs'.
  • Stairs: stairs comprise the flights, stair beams, landings and landing beams; where the stair joins the floor slab without a stair beam, the boundary is the nosing of the top tread plus 300mm; elevated concrete steps are itemised as 'stairs'. Under the quota scope the monolithic stair is measured on horizontal projection, without deducting stair wells narrower than 0.50m and without adding the parts built into walls.
  • Sundry members: handrails, copings, small pools and tanks, pads, door and window frames and other members each with a volume no more than 0.1m3 are itemised as 'sundry cast-in-place members' (GB/T 50854-2024 E.7.5).
  • Precast interface: balconies and air-conditioning slabs cast integrally with external wall panels follow the external wall panel items; those not cast integrally follow their own items (DB11/T 2382-2024 Clause 4.6.4).

VI. Walls

Beijing DB11/T 2382-2024: walls are measured by volume on the dimensions shown on the design drawings, without deducting the reinforcement, embedded inserts, door and window openings and individual holes no larger than 0.30m2, wall pilasters and parts projecting from the wall face being merged in; wall length on the centre line for external walls and the net line for internal walls; where a wall meets a slab, the wall height runs from the top of the base (ground beams) or the floor slab to the top of the floor slab above; where a wall meets a beam, the wall height runs to the beam underside; parapets run from the top of the roof slab to the parapet top, with parapet copings, waist mouldings and feature bands merged into the parapet. TB/T 10831-2024 notes 10(6): walls are measured by the centre-line length shown on the design drawings times the wall height and thickness, deducting door and window openings and holes over 0.30m2, with pilasters and projections merged into the wall volume. GB/T 50861-2024 C.8.4-3 (underground structures): wall height from the top of the base slab (or floor slab) to the top of the floor slab above; door and window openings and individual holes over 0.3m2 deducted; pilasters (attached wall columns), concealed columns, concealed beams and projections merged into the wall; the parts where slabs overlap walls go to the wall, the parts where beams overlap walls go to the beam. BOQ item split (GB/T 50854-2024 E.7.3): basement perimeter walls that retain earth are itemised as 'basement external walls', the remaining cast-in-place concrete walls as 'reinforced concrete walls'; the latter comprise, beyond the shear wall body, the shear wall columns (confined boundary elements, structural boundary elements, non-edge concealed columns and pilasters, in +, T, Y, L and straight shapes, reinforced column-style) and the shear wall beams (coupling beams, concealed beams, border beams); where a wall meets a column the wall runs to the column face, where a wall meets a beam the wall runs to the beam underside, and where a wall meets a slab the slab runs to the wall side; special-shaped columns whose section height-to-thickness ratio exceeds 4 in every horizontal direction are itemised as 'reinforced concrete walls'.

VII. Crossover-node attribution map (the same node lands on different members under different scopes)

Node Building quota / Beijing BOQ GB/T 50854-2024 Rail-transit underground GB/T 50861-2024
Column cap Beamless slab: cap merged into the slab, column height to the cap underside No separate cap item among the slab items; follows its slab item Cap merged into the column volume
Corbel Merged into the column Follows the column Merged into the column
Beam-column overlap Beam runs to the column side face (overlap to the column) Beam and column itemised separately, beam to the column side face Beam measured through; overlap to the beam
Wall column, wall beam (concealed column, concealed beam, coupling beam, border beam) Wall columns, wall beams and wall-face projections merged into the wall (Beijing, Jiangsu) Belong to 'reinforced concrete walls', merged into the wall Concealed columns and concealed beams merged into the wall
Wall-slab overlap Wall height to the top of the slab above, slab measured separately Slab to the wall side Slab-wall overlap to the wall
Beam-slab crossing Beam top meeting a slab: beam depth to the slab top; beam mid / underside meeting a slab: slab thickness not deducted (Jiangsu) Beam and slab itemised separately Beam depth from the beam underside to the slab underside

Error alert: measuring cast-in-place concrete walls is not 'external wall vertical projection area x wall thickness' - every scope above measures by volume on the design dimensions (centre-line length x wall height x thickness) with the 0.30m2 opening threshold; 'projection area x thickness' belongs to other sections (masonry, plastering, formwork contact area) and, applied to concrete walls, corrupts the opening-deduction and pilaster-merger rules.

VIII. Foundations and BOQ codes

BOQ foundation items (E.7.2): individual pile caps are itemised as 'individual foundations', cap beams as 'foundation tie beams', pile caps cast as a monolith as 'raft foundations'; the base slab of a box-type full raft foundation is itemised as a 'raft foundation', the remaining members being itemised separately as columns, beams, walls and slabs; frame-type equipment foundations are itemised separately as foundation, column, beam, wall and slab. Quota scope: where the cup depth of a cup foundation exceeds the cup length it ranks as a high-cup foundation, cup and high-cup foundations being measured on solid volume; equipment foundations other than block types are calculated on the respective items for foundations, columns, beams, walls and slabs, deducting reserved holes; where the rib height-to-width ratio is within 4:1 the foundation is a ribbed strip foundation, beyond 4:1 the base slab ranks as a plain strip foundation and what is above the base slab is measured as wall. The unified BOQ code for cast-in-place concrete members is 010502 (Appendix E, Table E.2.1).

Boundaries of applicability

  • This card serves construction-drawing budgets, BOQ preparation and settlement review in building and decoration works; municipal, railway and rail-transit works have their own measurement standards (rail-transit underground structures, for instance, per GB/T 50861-2024 Appendix C.8.4) whose interface rules may be the opposite - no cross-discipline borrowing.
  • 'Ribbed slabs at the sum of beam and slab volumes' holds only in the local consumption standards and traditional quota manuals that still carry such items (Beijing DB11/T 2382-2024, TB/T 10831-2024, Hunan 2025, Jiangsu 2026 and the like); under the GB/T 50854-2024 BOQ scope beams and slabs are coded separately and must not be merged.
  • Confirm the edition before use: GB/T 50854-2024 replaces GB 50854-2013; during the overlap the contract-agreed edition governs.
  • The 0.30m2 hole threshold for walls and slabs is per individual hole area, not total hole area; the test unit is the single opening.
  • This card resolves only the measurement of the concrete itself; formwork, reinforcement, scaffolding and the other preliminary items follow their own rules and are not merged in.
  • Member boundaries and deduction rules are ultimately governed by the measurement standard / consumption quota edition agreed in the contract; conflicts between regional and national standards are resolved by the contractual order of precedence.

Further reading

  • BOQ scope: GB/T 50854-2024, measurement standard for building and decoration works, Appendix E concrete and reinforced concrete works - general notes E.7.1, foundation notes E.7.2, column and wall notes E.7.3, beam and slab notes E.7.4, stairs and other notes E.7.5, item table E.2.1 (cast-in-place concrete members 010502).
  • Local consumption standards: DB11/T 2382-2024 'Consumption standard for construction works', Section 4.6 concrete and reinforced concrete works - notably Clause 4.6.4 (precast member boundaries), 4.6.5 (reinforcement) and 4.6.6 (measurement of cast-in-place members, item by item for columns, beams, walls and slabs); Jiangsu 2026 building and decoration consumption, Chapter 5 clauses on beams, slabs and walls; Hunan 2025 building and decoration consumption standard, clauses on slabs, walls, stairs and hollow floors.
  • Rail-transit scope: GB/T 50861-2024, measurement standard for urban rail transit works, Appendix C.8.4, cast-in-place concrete member clauses of underground structure works.
  • Railway scope: TB/T 10831-2024, railway works budget quota manual, Volume 10 'building works', volume notes '10. Measurement rules', items (1)-(12), covering columns, beams, walls, slabs, stairs, the erection of precast members and reinforcement length adjustments (post-tensioned anchorage length changes of 0.15m / 0.30m / 0.35m and the like).
  • Direction for comparative study: the differences between, and the pricing interface of, 'BOQ quantity (net dimensions, unmerged)' and 'quota quantity (per the consumption rules, merged)' for one and the same member.

Keywords

  • 现浇混凝土工程量计算
  • 柱高计算规则
  • 梁长算至柱侧面
  • 有梁板
  • 无梁板
  • 柱帽归属
  • 0.3m²孔洞扣减
  • 现浇混凝土构件010502
  • GB/T 50854-2024 附录E