Water supply and drainage pipeline quantities are computed by the centerline length shown on the design drawings: lengths occupied by fittings, valves and chambers are not deducted; construction wastage is not counted additionally
Water supply and drainage pipeline quantities are computed by the pipeline centerline length shown on the design drawings (linear meters), not by the actual installed length; the lengths occupied by valves, pressure reducers, steam traps, water meters, expansion joints and other fittings, and by the various chambers, are not deducted; the length occupied by square expansion compensators is added into the pipeline quantity; the additional lengths laid during construction for obstacle avoidance and bending are construction wastage and are not counted again. Municipal drainage follows a separate basis — "manhole centre to manhole centre, deducting the clear space of each inspection chamber" — and the applicable basis depends on the quota manual being executed for the project.
Applicable Codes
- GB/T 50856-2024 通用安装工程工程量计算标准 App. K Table K.1.1(code 031001)及说明第1~11条
- GB/T 50856-2024 App. K 9.1 管道界限的划分
- GB/T 50856-2024 App. H Table H.1.1/H.2.1/H.3.1 工业管道有关问题说明
- GB/T 50856-2024 App. C 静置设备与工艺金属结构制作安装工程(设备第一片法兰外配管列项)
- TB/T 10831-2024 铁路工程预算定额 Vol. 10 房屋工程 册说明十三(一)
- TB/T 10832-2024 铁路工程预算定额 Vol. 11 给水排水工程 册说明十二
- TB/T 10833-2024 铁路工程预算定额 Vol. 12 机务车辆机械工程 册说明四
- DB11/T 2382-2024 建设工程施工消耗量标准 第6.10.32、6.10.34、6.10.36条、第7.4.19~7.4.24条
- 京建发〔2021〕201号 2021预算消耗量标准 通用安装第十册 第一、二、五章 工程量计算规则
- SJG 181.4-2024 市政工程消耗量标准 Vol. 4 给水排水管网工程 1.2.3 管道铺设及Table 1.2.3
- SJG 111.4-2022 城市地下综合管廊工程消耗量标准(Vol. 4 入廊管线安装工程)1.2.1
- SJG 84-2020 市政维修工程消耗量标准 第二册 给水排水维修工程 管道功能性试验及冲洗消毒子目使用原则
Topic Positioning
The measurement basis for water supply and drainage pipeline quantities: computed by the pipeline centerline length shown on the design drawings (linear meters), not by the actual installed length. A comparative understanding of three bases — the national BOQ standard, the railway quota norms, and the municipal quota norms.
Core Conclusions
(1) Measurement basis: pipelines are computed in linear meters by the centerline length shown on the design drawings, not by the actual installed length; the additional lengths laid during construction for obstacle avoidance, bending, or cutting tolerances are construction wastage and are not counted again. (2) Non-deducted items: the lengths occupied by valves, pressure reducers, steam traps, water meters, expansion joints and other fittings, and by the various chambers, are never deducted (GB/T 50856-2024 Appendix K Table K.1.1 note 8; the TB/T 10832-2024 Volume 11 volume explanatory notes likewise make clear that the lengths of fittings and valves are already allowed for in the construction wastage). (3) Special rules: square expansion compensators are added into the pipeline installation quantity at their occupied length (the all-in unit rate includes their fabrication and installation); directly buried pre-insulated pipes are instead listed under industrial pipelines (Appendix H); pipeline protective casings are listed by the corresponding material; branch pipes are measured from the main-pipe centerline to the centre of the terminal junction; pipe jacking is measured by the design length. (4) The work content already includes pressure testing (hydrostatic / pneumatic / watertightness / ball-passing / vacuum, etc.) and flushing and cleaning, and these are not counted again.
Applicable Boundaries
Applies to: BOQ measurement of indoor and outdoor water supply and drainage, heating and gas pipelines of buildings (code 031001) and the water supply and drainage quota norms of the various sectors. Note the difference in basis: municipal drainage (e.g. Shenzhen SJG 84-2020) is computed by the manhole-centre-to-manhole-centre centerline length and deducts the clear-space length of each inspection chamber (deduction lengths per the quota table), unlike the national rule that "chambers are not deducted" — execute according to the quota manual applicable to the project. It does not apply where the contract provides otherwise and requires measurement by actual length.
Further Reading
GB/T 50856-2024 Standard for Measurement of General Installation Works Quantities, Appendix K Table K.1.1 and notes 1~11; TB/T 10832-2024 Railway Works Budget Quota Manual, Volume 11: Water Supply and Drainage Works, volume explanatory notes "XII. Quantity calculation rules"; Shenzhen SJG 84-2020 Consumption Standard for Municipal Maintenance Works, Volume 2: Water Supply and Drainage Maintenance Works, Section 1.2.2 table of deduction lengths per chamber.
Keywords
- 给排水管道工程量计算
- 不扣除阀门管件所占长度
- 管道中心线长度 延长米
- 方形补偿器 并入管道工程量
- 阀门井 检查井 扣井长度
- GB/T 50856-2024 表K.1.1
- 管道室内外界限划分
- 试压临时管线摊销
Related Cards
- →
Deduction rules for quantity take-off of ductwork fabrication and installation: the developed area deducts no area of inspection holes, measuring holes, supply outlets or extract inlets; duct length follows the centreline shown on the design (elbows, tees and other fittings included) minus the length occupied by dampers and other components, which are listed and measured separately under code 030703 (conventions of GB/T 50856-2024 and local consumption standards)
The developed area of ducts deducts no area of inspection holes, measuring holes, supply outlets or extract inlets; duct length follows the centreline length shown on the design (main and branch ducts divided at the intersection of their centrelines), including elbows, tees, reducers and round-to-rectangular transitions but excluding (deducting) the length occupied by dampers and other components; the developed area excludes overlapping areas of ducts and duct mouths. Dampers, grilles, diffusers, silencers and other components are listed separately under the corresponding component items (code 030703) and measured by the number shown on the design (plenum boxes by developed area, without deducting opening areas).
- →
GB/T 50856-2024 "no deduction of valve and fitting lengths" for piping is measurement-only: industrial piping (Appendix H) lists fittings/flanges/valves separately; water supply/drainage/heating/gas (Appendix K) merges fittings into piping
In GB/T 50856-2024 (replacing GB 50856-2013, effective 2025-09-01), "piping quantities do not deduct lengths occupied by valves, fittings, or square compensators" is only a length-measurement rule and is separate from whether fittings get their own BOQ items. Industrial piping (Appendix H, code 0308): piping measured in m along the design centerline, while fittings, valves, and flanges are independent BOQ items (counted by "piece/sheet") — elbows, tees, and flanges must be listed and priced separately. Water supply/drainage, heating, gas (Appendix K, code 0310): piping in m without deducting lengths of valves, pressure reducers, traps, water meters, expansion joints and other fittings or various chambers; square compensator length merges into piping, and its fabrication and installation are included in the all-in unit rate for piping; pressure testing, purging and flushing are piping work content; elbows, tees and other fittings merge into piping items without separate listing.
- →
Overview of quantity take-off for construction works: basis, general rules and per-trade calculation methods
Quantity take-off rests on the four-tier basis "contract agreement -> design drawings -> approved project execution plan (construction methodology and site organization) -> appendix rules of the quota norms/measurement standards"; except where rules provide otherwise, all quantities are computed from the dimensions shown on the design drawings. General rules include: calculation per appendix rules (mandatory provisions of codes); the no-deduction threshold of single holes <=0.3 m2; significant figures of units of measurement (t/km three decimals; m/m2/m3/kg two; counts integer); and dual-track BOQ vs quota-norm quantities. Earthwork, concrete, reinforcement, formwork, masonry, waterproofing, finishes etc. each have standard algorithms.
- →
Quantity take-off (measurement) follows design-drawn dimensions (measurement per drawings): general principle, rule exceptions, and final account linkage
Quantities are in principle calculated from design-drawn dimensions (measurement per drawings), not from actual site dimensions; only items where the method of measurement "provides otherwise" (e.g. earthwork by natural in-situ (undisturbed) volume, depth taken from surveyed elevation) and site instruction / variation record items not specified in the design (flowing sand and silt provisionally estimated, concealed works) are measured per actual conditions / site instruction / variation record. Parts constructed beyond design dimensions without variation or site instruction / variation record support are generally not measured in the final account.
Cited By
- ←
Pricing and setting of pressure-reducing orifice plates in fire-water systems: quota item selection (Tianjin 7-31 to 35, Beijing 1-68 to 72, DB11/T 2382-2024 C9-1-68 to 72), counting per piece regardless of mounting position, companion flanges added as design quantities without double counting, the boundary against pressure-reducing valve sets (static versus dynamic pressure), and the mandatory code rules on orifice position and construction
Orifice-plate installation is counted per piece and graded by nominal diameter into pressure-reducing orifice plate installation items (Tianjin 2025 volume 7, 7-31 to 35; Beijing 2021 volume 9, 1-68 to 72; DB11/T 2382-2024 C9-1-68 to 72); whether installed in a flange, a union or a hydrant interface, the same item applies, and the item already covers pre-installation, removal and re-installation. The flange body is not included: when installed inside a flange pair, 'the flange quantity shall be calculated separately per the design drawings' (the two plates gripping the orifice count as one pair in the pipeline flange quantity), while the steel-pipe flanged-connection item already includes fitting and flange installation - so the same pair must never run the flange installation item again. Orifice plates reduce dynamic pressure only (installed downstream of alarm valves on distribution pipes and branches, orifice diameters stepping down where distribution-pipe inlet pressures exceed 0.40 MPa), whereas pressure-reducing valves cut both static and dynamic pressure (installed ahead of the alarm valve set) - the two are not interchangeable.
- ←
Quantity take-off and double-counting prevention for field joint coating and damage repair of factory-prefabricated anti-corrosion pipes: whole-pipe anti-corrosion quota line items must not be re-applied; joint coating counted by weld count (per joint/spot) with per-joint nominal length converted to area; damage repair graded by damage size; dual-track pricing of BOQ m2 versus quota joints
The factory-applied anti-corrosion coating cost is already inside the material price of finished coated pipes, so only field joint coating and damage repair may be counted on site; painting, anti-corrosion coating or coal-tar epoxy quota line items must not be applied again over the whole pipe length or surface (GB/T 50856-2024 clause 3.0.8 opens an exception only for painting the design expressly requires to be completed on site and for repainting in reconstruction or extension projects; DB11/T 2382-2024 clauses 7.4.52 and 7.4.53 confine field anti-corrosion to the joints - heat-shrink sleeves and three-layer polyethylene heat-shrink tape are measured by weld count, and coating-type joint methods take the same-scope line item with labour x 1.10). Joint coating count = number of girth welds (standard-length sections - 1, plus fittings, valves and tie-in joints); developed area per joint = pi x pipe OD x nominal length per joint (400 mm for OD no more than 426 mm, 600 mm for OD above 426 mm); the BOQ item is measured in m2 of design-shown surface area per GB/T 50856-2024 table M.9.1 (code 031209) while the quota counts per joint/spot, so units must be converted before pricing; damage repair is treated per spot, graded by damage depth and puncture size (GB/T 50538-2020 clause 8.5.1).
- ←
Checking order when pipe specifications on the drawings conflict with the BOQ description: the dimension figures on drawings govern and conflicts are clarified through drawing review; at pricing level, unit-rate contracts follow the bill of quantities and lump-sum contracts follow the contract drawings and specifications
The test runs on two levels. (1) Annotation level: dimensions on drawings are governed by the dimension figures and shall not be scaled directly off the drawing (GB/T 50001-2017 Clause 11.2.1); design documents must be qualified and valid, and survey briefings, design disclosure and drawing review must be carried out with records kept (GB 55032-2022 Clause 3.1.1). The review checks drawing validity, compliance of content with national technical codes, and coordination among disciplines and between general drawings and details -- a pipe bore contradiction must be clarified through the review and recorded, not resolved by unilateral choice. (2) Pricing level: for works under unit-rate contracts, where the contract drawings are inconsistent with the tender work-item BOQ during performance, the bill of quantities governs; under lump-sum contracts, where the contract drawings and specifications are inconsistent with the priced BOQ, the contract drawings and specifications govern (GB/T 50500-2024 Clause 3.4.5). BOQ item descriptions must state specification, installation location, medium and the like item by item; one and the same pipe must not be listed twice under both DN and de designations.
- ←
Itemisation attribution and measurement coverage of valves, flanges, strainers and expansion joints in pipe erection: the boundary between the two regimes of GB/T 50856-2024 Annex K pipe accessories (031002) and Annex H valves and flanges (030807~030812), the 'included in pipe erection vs itemised separately' boundary, and the quota rate build-up conversions
Valves, flanges, strainers and expansion joints are all pipe accessories and must not be merged into pipe erection items; they must be itemised separately by works category: building water supply and drainage, heating and gas follow GB/T 50856-2024 Annex K Table K.2.1 pipe accessories (code 031002); industrial piping follows Annex H (valves 030807~030809, flanges 030810~030812, valves counted per unit from the design-drawn quantity); municipal pipe networks follow GB/T 50857-2024 Table E.2.1 (040502). Pipe length never deducts the length occupied by valves, pressure reducers, steam traps, water meters, expansion joints and other accessories or by chambers of any kind; the square expansion loop is the only reverse exception (its occupied length merges into the pipe and its fabrication and erection are already in the all-in unit rate); a valve's work content excludes flanges and flanged accessories, and where fittings are flange-connected they are measured as flange items and the fitting item ceases.
- ←
GB/T 50856-2024 "no deduction of valve and fitting lengths" for piping is measurement-only: industrial piping (Appendix H) lists fittings/flanges/valves separately; water supply/drainage/heating/gas (Appendix K) merges fittings into piping
In GB/T 50856-2024 (replacing GB 50856-2013, effective 2025-09-01), "piping quantities do not deduct lengths occupied by valves, fittings, or square compensators" is only a length-measurement rule and is separate from whether fittings get their own BOQ items. Industrial piping (Appendix H, code 0308): piping measured in m along the design centerline, while fittings, valves, and flanges are independent BOQ items (counted by "piece/sheet") — elbows, tees, and flanges must be listed and priced separately. Water supply/drainage, heating, gas (Appendix K, code 0310): piping in m without deducting lengths of valves, pressure reducers, traps, water meters, expansion joints and other fittings or various chambers; square compensator length merges into piping, and its fabrication and installation are included in the all-in unit rate for piping; pressure testing, purging and flushing are piping work content; elbows, tees and other fittings merge into piping items without separate listing.
- ←
Deciding the relation between bell-and-spigot joints and rubber-ring joint items: joint nature (rigid cement caulked / flexible rubber ring) -> quota basis (joint inside the pipe-laying metre, or a joint item counted per piece) -> whether the ring double-charges, split by pipe material (cast iron / reinforced concrete / plastic) and quota system
Bell-and-spigot is only an end construction, never a pricing basis: cement or asbestos-cement caulked joints (oakum packing included) are rigid; rubber rings, flanged gland plus ring, and clamp plus ring are flexible. Where the joint method is written into the pipe-laying item's name or work content, it is inside the metre-priced laying - never add a 'ring joint' item; only where the quota lists joints as items (railway pipe-jacking joints PY-407~PY-414; municipal collar joints / caulking) do joints count per piece or per ten. Rings as joint auxiliaries already sit in the item's materials (ductile iron laying lists rubber ring at 0, i.e. supplied none extra); pipe main materials outside the base price price separately per the annex table - rings never charge twice.
- ←
Preventing double counting of earthworks where trench, manhole pit and spread foundation pit overlap: physical overlap versus intersection of battered faces, assigning the manhole-length section by the larger cross-section, the pit deepening increment, pipe-joint working pits already included, and one trench width taken once for multi-pipe runs
Three tests prevent double counting: (1) physical overlap (the same space excavated twice) is counted once, and battered-face intersections are expressly 'not deducted' by most quota manuals (Hunan 2025 IV.4; SJG 111.1-2022 table 1.2.3-1 note 2; SJG 84-2020 table 7.2.9 note 1); (2) the BOQ quantity (GB/T 50857-2024, drawn dimensions plus working space, no batter) and the quota quantity (working space plus batter) are computed independently - never mix then deduct; (3) the manhole-length section is assigned by section size: if A-pit is no less than A-trench the section counts as pit and the trench length is reduced by that section, if A-pit is smaller the manhole length merges into the trench and no pit is listed, the total taking the max, not the sum; where the pit floor lies below the trench floor, the deepening increment delta V = A-pit x (H-pit - H-trench) is added; pipe-joint working pits and manholes along the line are covered by 2.5% of the trench earth and rock quantity (1.5% for wells and joint pits in the railway volume 12), not listed separately.
- ←
Deduction rules for quantity take-off of ductwork fabrication and installation: the developed area deducts no area of inspection holes, measuring holes, supply outlets or extract inlets; duct length follows the centreline shown on the design (elbows, tees and other fittings included) minus the length occupied by dampers and other components, which are listed and measured separately under code 030703 (conventions of GB/T 50856-2024 and local consumption standards)
The developed area of ducts deducts no area of inspection holes, measuring holes, supply outlets or extract inlets; duct length follows the centreline length shown on the design (main and branch ducts divided at the intersection of their centrelines), including elbows, tees, reducers and round-to-rectangular transitions but excluding (deducting) the length occupied by dampers and other components; the developed area excludes overlapping areas of ducts and duct mouths. Dampers, grilles, diffusers, silencers and other components are listed separately under the corresponding component items (code 030703) and measured by the number shown on the design (plenum boxes by developed area, without deducting opening areas).
- ←
Preventing double counting of pipes and fittings in fire water extinguishing systems: length by centreline without deducting fittings, threaded fittings absorbed into the pipe quota line items, grooved fittings counted separately per 'set' (with clamp duplication checks and size-band omission checks)
Fire piping has a single layer of length measurement: by the pipe centreline length shown on the design drawings, without deducting valves, fittings and components (DB11/T 2382-2024 clause 6.9.13; Beijing 2021 volume 10 chapter 2 measurement rules: 'pipes are measured by length along the centreline shown on the drawings, without deducting fittings, valves and attachments; fitting installation is measured by the quantities shown'). Fittings split into two bases: for galvanized steel pipe (threaded), the pipe consumption already includes fitting installation, and fitting material quantities follow the drawn quantities or table 6.9.14 contents (pieces/m: DN25 total 0.590, DN50 0.808, DN100 0.520) - threaded fitting installation or main material must not be listed again; for steel pipe (grooved), the pipe item covers only the grooved straight coupling, and grooved elbows, tees and crosses are separate fitting installation items counted per 'set' by drawn quantity, each set including the clamp and seal ring (clause 6.9.16, matching the two item sets of volume 9 fire works, 'fitting installation (grooved coupling)' and 'fitting installation (cut-in connection)', e.g. DN100 grooved 9-1-35, cut-in 9-1-25). The only source of duplication is listing the 'clamp' three times: the sensible clamp ceiling = pipe length x grooved-coupling content of the pipe item (about 0.1667 set/m) + fitting count x grooved-coupling content of the fitting item (1.005 set/set); for DN100, 100m and 20 fittings that is 16.67 + 20.1 = 36.77 sets - a markedly higher figure signals duplication.
- ←
BOQ itemisation boundary for earthworks, bedding, masonry, chambers and thrust blocks attached to installation works: the routing rules by which GB/T 50856-2024 Clause 3.0.4 refers to GB/T 50854 / GB/T 50857 / GB/T 50858
Per GB/T 50856-2024 Clause 3.0.4, earthwork excavation and backfill, bedding, masonry, plastering, trench cover slabs and cast-in-place foundations involved in installation works are itemised under the corresponding items of GB/T 50854; wells, precast pipelines, pipe thrust blocks, new-to-existing pipe connections, temporary blow-off pipelines, warning tapes / marker posts / warning signs, and waste incinerator and auxiliary equipment installation are itemised under the corresponding items of GB/T 50857; fountains, misting systems and irrigation systems are itemised under GB/T 50858; the pipe proper remains measured under Appendix K (031001) by centreline length, with no deduction for the lengths occupied by wells.
- ←
Quantity demarcation and length measurement between risers and branch pipes in water supply and drainage (heating, gas) piping: risers accumulated segment by segment by design level difference (storey-height accumulation only as a check), the tee/cross intersection on the riser centreline as the demarcation point, branch pipes measured from that centre to the fixture inlet, vertical segments measured on isometric drawings and horizontal segments on plans, same-floor versus floor-through drainage branch differences, and parallel risers in one shaft listed pipe by pipe
Riser length is accumulated segment by segment along the pipeline centreline shown on the design as upper level minus lower level; storey-height accumulation is only a check value and never a measurement basis. The demarcation between riser and branch is the tee or cross intersection on the riser centreline; the branch runs from that centre point to the centre of the farthest fixture or equipment connection, and the length of the tee fitting itself is neither deducted nor added (fitting installation is already inside the piping item). Parallel risers sharing one shaft must be itemised pipe by pipe by material, connection form and specification, never merged into one measurement.
- ←
Quantity take-off of cable tray and wireway body length: the segmented formula L = Sum(L_h) + Sum(L_v) for horizontal segments (L_h) and vertical segments (L_v), measurement against the dimensions shown on the design drawings, and the rule of no deduction for bends and tees (Beijing 2021 Consumption Standard, Volume 4, Chapter 11)
Cable trays and wireways are measured by length (extended metres, unit m) against the dimensions shown on the design drawings, without deducting the length occupied by bends and tees. Practice applies the segmented summation formula L = Sum(L_h) + Sum(L_v): horizontal segments are measured along the tray centreline path shown on the plan, vertical segments follow the level difference of the two ends L_v = |H_top - H_bottom| (both ends taken from the same datum); different materials or sizes are accumulated separately, and path increments caused by MEP coordination detours do not adjust the quantity.
- ←
BOQ rules for measuring cable trays and raceways by the metre, and the pricing boundary of fittings such as elbows and tees (no separate BOQ itemisation, the installation cost of fittings included in the tray installation quota line item, fire stopping measured separately)
Cable trays and raceways are invariably measured in length 'm' as shown on the design drawings, not by 'piece/unit'; the lengths occupied by elbows, tees, crosses and reducers are not deducted (DB11/T 2382-2024 Clauses 6.4.106 and 6.4.111); at BOQ level they are not itemised separately, and at quota level the installation cost of the fittings is already included in the work content of the tray installation line item (e.g. Beijing line item C4-11-253, whose work content includes 'elbows, tees or crosses... support and hanger installation, earthing'), so no separate installation line item may be applied 'per piece'; fire stopping of holes where trays pass through fire compartment walls is measured separately under fire barrier board and similar items (Beijing C4-8-497, in m2) and is not included in tray installation.
- ←
Quantity calculation of duct and pipeline thermal insulation: formulas and BOQ listing (GB/T 50856-2024 Appendix M)
Insulation works are uniformly listed under GB/T 50856-2024 Appendix M (code 031208): insulation layers in m3, protective/vapor barriers in m2. Pipeline insulation volume V = π x (D + 1.033δ) x 1.033δ x L (the original adjustment coefficients in GB/T 50856-2024 M.11.10 problem note 6 are 1.03 and 2.1; TB/T 10833-2024 uses 1.033 — the same caliber expressed with different precision); duct insulation is computed as developed area x calculated thickness, the developed area by centerline length including bends, tees and other fittings but excluding components, without deducting inspection holes and supply outlets; multi-layer work is computed layer by layer, heat-traced pipes first derive the comprehensive value D', and derusting/painting before insulation are listed separately under Appendix M.1.
- ←
Pricing and measurement of CCTV/QV/sonar in-pipe inspection: extended metres along the centre line of the pipe or culvert without deducting manholes, line items banded by diameter and inspection method, working conditions (water level, clearing and cleaning) and excluded work charged separately
CCTV in-pipe inspection of pipelines is measured in metres (m) by the extended length of the centre line of the pipe or culvert as designed (actually inspected), without deducting the length occupied by fittings or manholes; the CCTV line items are banded by internal diameter or height of the pipe, with 100m as the line-item unit, and QV and sonar likewise. The line items comprehensively allow for differences of pipe type, material and age, but exclude pipe plugging and reinstatement, desilting, culvert-wall washing, dewatering, and image analysis and assessment, digital mapping and archiving, and compilation of inspection deliverables, which are charged separately when they occur; desilting for the inspection and repair categories is charged at the labour, material and plant of the corresponding items multiplied by a factor of 1.5.
- ←
Measuring and pricing the hand-laminated joints of GRP pipes and ducts (resin-impregnated lay-up joints, resin filling and joint reinforcement): the lamination sits inside the pipe / fitting / duct installation items' work content, not itemised separately; only where the joint form exceeds the quota range does it count separately per joint or per developed lamination area
The hand-laminated joint of GRP pipes and ducts is no independent quota item: its resin filling, glass-cloth reinforcement and glue-smeared insertion are written into the work content of the pipe (fitting) / duct installation items, so pricing follows pipe length (m, unit 10 m, on the drawn centre line without deducting fittings and valves), fitting count (pieces, unit 10) or duct developed area (m2, unit 10 m2), not per joint; only where the designed joint form exceeds the quota's scope (site butt joints with double-sided lamination, hand-laminated joints of finished ducts on site) does it count separately per joint or per developed lamination area, applying hand-laminated GRP items (GB/T 50856-2024 Appendix M Table M.3.1, code 031203) or a supplementary quota compiled on quota principles and approved.
- ←
Measuring and pricing drainage (discharge) pipes: fixing the measurement basis and quota items by scenario - roofs, urban rail transit, municipal bridges and culverts, railway bridge decks
Drainage pipe measurement splits by scenario: pipe bodies (downpipes / drainage pipes / the discharge pipes themselves) by drawn length in m (extended metres), and finished parts - discharge outlets, rainwater heads, hoppers, drain inlets - by count (per set / per piece). Building roofs follow DB11/T 2382-2024 Articles 4.10.21 to 4.10.23 (downpipes by length; hoppers, bends and drain inlets by count; roof drain (drip) pipes and vent pipes by count); urban rail follows Article 10.1.90 of the same standard (discharge pipes by length); municipal bridges follow SJG 181.2-2024 Article 7.2.4 (drainage pipes and weep holes by length in metres); railway bridge-deck drainage quotas count per 10 extended metres. The same member carries different units across industry quotas - apply the volume the project executes.
- ←
The per-set (per-group) measurement of sanitary ware: what water and drainage fittings a set contains, how twin (double-basin) wash basins count, and whether fixture-matched fittings charge separately
GB/T 50856-2024 Table K.3.1 sanitary ware (code 031003) counts per set on the drawn quantity; one set = the fixture + the full water supply fittings (taps, flexible hoses, valves, flush pipes, sprays) + the full drainage fittings (traps, waste plugs, drain inlets) + the fixture's connecting pipes; non-independently installed fittings already sit in the fixture's work content and are not re-listed. The standards set no twin wording for double basins - deriving from one set = one basin position: two basins each independently supplied and drained count 2 sets; a one-piece twin sharing one supply and drain counts 1. Fitting installation costs are inside the fixture items and not re-charged, materials priced separately as unset main materials; only independently installed taps, floor drains and floor cleanouts itemise and measure alone.
- ←
Distinguishing the measurement units of duct flexible joints (flexible connections / canvas connections) and piping flexible connections (soft joints, metal hose, expansion-joint compensators): the former by developed area in m2, the latter by quantity shown on the drawings per piece / per length
Duct flexible joints (canvas connections, flexible short ducts and duct expansion joints, under ventilation and air-conditioning duct components 030703 flexible connections) are measured on the dimensions shown on the drawings by developed area in m2, not by count; piping flexible connections (soft joints / metal hose, expansion joints i.e. compensators, under water supply, drainage, heating and gas pipe accessories 031002) are measured by the quantity shown on the drawings per piece (soft joints / hose per length), not in m2; whole extensible flexible ducts (030702) are measured separately on centre-line length in m - the three must not be mixed.
- ←
Quantity calculation and quota application for metal protective cladding (aluminium sheet, galvanised iron sheet) over pipe insulation
Metal cladding over pipe insulation is measured in developed cladding area m2, not by pipe length or insulation volume; calculated by the GB/T 50856-2024 Appendix M Table M.11.10 notes item 6 formulas (insulation V = pi x (D + 1.03d) x 1.03d x L; vapour barrier / cladding S = pi x (D + 2.1d) x L, D being pipe outside diameter, d insulation thickness, L pipe extended length); apply the metal cladding items of the painting, anti-corrosion and insulation chapter, banded by material (galvanised thin steel sheet, aluminium alloy sheet etc.) and thickness, pipes and equipment listed separately, seaming and lap wastage already in the material consumptions; pipes over 720 mm diameter are treated as equipment; flange and valve insulation box cladding is calculated separately per Table M.11.10-1.
- ←
Quantity calculation and consumption-standard sub-item application for grooved-connection fittings of sprinkler pipes (mechanical tees, grooved fittings, couplings/clamps) - mainly Beijing DB11/T 2382-2024
Sprinkler pipes are calculated by the centre-line length shown on the design, without deducting the lengths of fittings and components; mechanical tees/crosses (hole-cut type) apply the "steel pipe (grooved connection) hole-cut fittings" sub-items, finished elbows/tees/crosses apply the "steel pipe (grooved connection) grooved fittings" sub-items - both measured per "set" by the design quantities, each set including the clamp and gasket (material content 1.0050 set/set); couplings are not itemized separately - butt joints of straight pipes are included in the pipe sub-items (grooved coupling 0.1667 set/m, about one per 6 m), and couplings at fittings are included in the fitting sub-items. GB 50261-2017 Clause 5.1.11: mains (risers) and horizontal pipes shall not be connected by mechanical tees; the hole spacing of mechanical tees shall not be less than 500 mm and of mechanical crosses not less than 1000 mm.
- ←
Measurement caliber for municipal drainage pipes and rainwater-inlet connectors: by design centerline length without deducting manholes and inlets (Beijing/national), versus regional manhole-deducting calibers
Beijing DB11/T 2382-2024 matches GB/T 50857-2024: drainage pipes (including inlet connectors) are computed by design centerline length, without deducting manholes, inlets, and other auxiliary structures — there is no "center or edge" datum question; some cities (e.g., Shenzhen SJG 181.4-2024 Clause 1.2.3) deduct each manhole's length from center-to-center lengths — a regional difference; confirm local rules before cross-region compilation.
- ←
Beijing DB11/T 2382-2024 consumption standard: pricing application of the water-tightness test and ball-passing test of drainage pipelines (water-tightness test included in the pipe-laying sub-items, ball-passing test handled by coefficient adjustment on the indoor pipe-installation sub-item - neither itemized separately)
Under Beijing DB11/T 2382-2024 neither test is applied under a separate sub-item: the water-tightness test is already included in the consumptions of "drainage pipeline laying" (7.4.26 - no separate sub-item, no separate BOQ item); the ball-passing test is handled by coefficient adjustment on the indoor drainage pipe installation sub-item (labor x 1.10, other-materials fee ratio +1.00%, other-tools fee ratio +0.05%, 6.10.30, triggered only when required by the design or the code); indoor pipe hydrostatic testing and water flushing are included in the installation consumptions (6.10.25), and the work content of drainage plastic-pipe sub-items additionally includes the water-filling test (e.g. C10-2-104).
- ←
Beijing DB11/T 2382-2024: determining chapter by chapter and material by material whether pipe installation quota line items include pipe fittings (gas piping: only galvanized steel pipe with threaded joints includes fittings; indoor water supply/drainage and heating piping include fittings)
Beijing DB11/T 2382-2024: in gas piping, only the galvanized steel pipe (threaded joints) installation items include fittings and pipe clamps (6.10.34); for welded steel pipe, PE pipe and other materials, the fittings must additionally follow the "fitting and pipe-clamp installation" items; the indoor water supply, drainage and heating piping runs the opposite way - the pipe installation items include the fitting installation content, the fitting materials being taken as the design-shown quantities or per Table 6.10.32 (6.10.32). Pipes are measured along the design-shown centreline length without deducting the lengths occupied by fittings, valves and accessories (6.10.36); fittings are measured as the design-shown number of pieces (6.10.37).
- ←
Measurement rules for the matching flanges of flanged valves: in water supply/drainage, heating and gas works the flanges are not applied separately, while in industrial-pipeline works the valve and its matching flanges are calculated separately (DB11/T 2382-2024)
Per the Beijing local standard DB11/T 2382-2024 "Construction Consumption Standard", general installation works: in water-supply-and-drainage, heating and gas works, the flanged-valve installation sub-items are compiled on the basis of flange connections on both sides - the matching flanges and bolts are included in the valve installation sub-items and flange installation sub-items are not applied separately (where only one side is flanged, the flange and bolt quantities are halved, a consumption adjustment); in industrial-pipeline works "the installation of all flanged valves and the installation of the matching flanges shall have their quantities calculated separately" (6.8.54) - the valve sub-item does not include installation of the flange body (only the installation of one gasket and one set of flange bolts, with bolt materials charged separately), and the matching flanges must be applied under separate flange-installation sub-items; the same basis applies to medium- and high-pressure valves (6.10.52, 6.8.73 to 6.8.79).
- ←
Sorting out the measurement of underfloor heating coils (floor radiant heating pipes): the bill measures the net area of heated rooms (m2), the quota measures the design-shown pipe length (m), and the boundary between heating pipes and manifolds
Bill (measurement) basis: GB/T 50856 Annex K table K.4.1 "heating appliances" (code 031004) measures floor radiant heating by net heated-room area in m2. Quota (consumption) basis: floor radiant heating pipe laying is computed by design-shown length in m (e.g. Beijing DB11/T 2382-2024 clause 6.10.76); the two are bridged by the net-area-to-pipe-length contents of table 6.10.76 (pipe OD 16 mm = 6.300, 20 mm = 5.775, in m per m2 of net area). The boundary with manifolds sits at the branch-pipe connections off the distributor: on the heating-pipe side, from the distributor outlet to the collector connection (including the riser from floor level to the connecting fitting); the heat-medium distribution and collection unit (manifold) is listed separately per "set".
- ←
Measurement of metal-surface rust removal (and painting, anti-corrosion): routed by object - plant and piping by area m2, metal structures by theoretical mass t/kg - with the companion rule of matching the unit of the quota item applied
Rust-removal quantities route by the OBJECT treated, not an either-or: plant and piping rust removal is computed by area (m2) on the design-shown surface, metal-structure rust removal by the theoretical mass of the structure (DB11/T 2382-2024 clauses 6.12.8, 6.12.9), and the outcome must match the unit of the quota item applied. Within metal structures a further split applies: general steelwork (hangers, supports, brackets, ladders, railings, platforms) and pipe-rack steelwork measure in kg; steelwork of sections over 300 mm and H sections over 300 mm measure by developed area in m2 (GB/T 50856-2024 Annex M table M.1.1 note 8); pipe surface S = pi x D x L, with fittings, valves, flanges, manholes and nozzle irregularities comprehended and not added. The municipal basis agrees (DB11/T 2382-2024 clause 7.4.51: pipe rust removal and painting on pipe surface area; steelwork rust removal and metal-structure painting on theoretical mass).
- ←
Determining BOQ attribution of gas pipelines: the boundary between GB/T 50856-2024 Appendix H (industrial piping) and Appendix K (water supply/drainage, heating, gas), and the division with municipal GB/T 50857-2024
Gas pipelines are not an either-or between "industrial piping" and "installation works" — both are appendices H and K of the same GB/T 50856-2024. Two yardsticks: (1) first the municipal boundary — heat and gas pipelines are bounded at the first meter (valve) at the plant entrance; beyond (the municipal side), list per GB/T 50857-2024 Appendix E network works (pipe laying 040501); (2) then by use — production (workshops, plants, stations, tank farms and between them) or shared production/domestic -> Appendix H industrial piping (030801 low/030802 medium/030803 high pressure by pressure class); domestic -> Appendix K (Table K.1.1, code 031001). High-pressure pipes, stainless pipes and their fittings/valves, weld NDT, and directly buried pre-insulated pipes are all listed under Appendix H.
- ←
Pipe jacking pricing: working/receiving shafts, jacking quantity rules, and the short-distance adjustment factor (SJG 181.4-2024)
Pipe jacking costs fall into four blocks: working/receiving shaft construction (open caissons apply tunnel-volume sub-items; working-pit bedding/foundation labor x 1.10), installation/removal of jacking equipment and facilities, jacking operation, and separately charged costs. Jacking quantities are measured in meters by design jacking length; when the total length of extrusion-type jacking with pipe diameter <= 1650 mm is <= 100 m, or the total length of earth-pressure/slurry/air-pressure/compound jacking is <= 50 m, the labor and machine-shifts of jacking sub-items are multiplied by 1.30; spoil hauling, slurry treatment and transport, and groundwater dewatering/drainage are all charged separately.
- ←
Sleeves for rainwater/soil (drainage) pipes through floors: mandatory setting, dimensions and construction, and BOQ measurement (GB 55020-2021 / GB/T 50856-2024)
Indoor rain/soil (drainage) pipes through floors shall have metal or plastic sleeves (GB 55020-2021 Clause 8.2.3, fully mandatory): in-floor sleeve tops 20 mm above the finished floor (50 mm in bathrooms and kitchens), bottoms flush with the slab soffit; the sleeve-pipe gap packed with flame-retardant dense material and waterproof ointment, pipe joints not inside sleeves; sleeve size, where unspecified, two nominal sizes larger (DB11/T 1832.13-2022 Clause 3.4.4); BOQ per GB/T 50856-2024 Appendix N (031301003) by count per design quantity, different sleeve classes listed separately.
- ←
Calculating fire-protection system commissioning fees: BOQ listing, measurement units, and point-count rules (GB/T 50856-2024 Appendix J, code 030909)
Fire-protection system commissioning fees are listed separately in the BOQ (GB/T 50856-2024 code 030909), not charged as a percentage of the works cost, but measured by system/point/count with commissioning items: water extinguishing control devices by points from flow indicators/hydrant pump-start buttons/monitor counts, gas extinguishing by cylinder-valve count as points, automatic alarm and other systems by device counts as points and measured by "system", fire barrier control devices by count (valves) or unit (fire lifts); when applying quotas, price by the point-tier steps of the chosen quota — local standards differ in caliber.
- ←
Drainage-pipe testing caliber and pricing inclusion boundary: gravity pipes take leakage-tightness tests (water/air) not pressure tests/disinfection-flushing; tests are included in the pipe BOQ item, norm items listed separately != separate BOQ items, with a four-step omitted-item test for settlement
Drainage pipes are gravity pipes; their functional test is the leakage-tightness test (water test/air test) — there is no "pressure test" caliber and no water-supply disinfection-flushing: sewage, combined, and storm pipes in collapsible/expansive/quicksand soils must pass tightness tests before use (GB 50268-2008, 9.1.11, mandatory). At BOQ level the test is inside the pipe item (GB/T 50856-2024 Table K.1.1 note 9; GB/T 50857-2024 Annex E and 4.1.2 "shall not be split into separate items"); at norm level separate test items may price it (e.g., SJG 181.4-2024), but a separate norm item != a separate BOQ item. "Drainage-pipe disinfection-flushing/pressure test" in settlements is a wrong item — strike it.
- ←
Indoor/outdoor boundaries for water-sewer, heating, gas, and fire-water pipes: scope of the 1.5m-outside-wall rule, manhole/valve attribution, and railway vs Beijing system differences
Water and heating pipes divide indoor/outdoor at 1.5m outside the building face (at the entrance valve where set; heating with an outdoor entrance unit at the circulation-pipe tee); drainage at the first exit inspection well — the 1.5m rule does not apply to drainage; gas by entry type at the first indoor valve (underground) or first tee outside the wall (above ground) (GB/T 50856-2024 Annex K K.9.1). Boundary components: valves belong to water/sewer works, wells to outdoor installation works (SJG 77-2020, 6.1.4). Railway has no 1.5m band: water at the entrance meter or junction well (direct entry at the building face), drainage at the first exit well (or septic tank) (TB/T 10832-2024 Vol. 11 volume notes).
- ←
Pricing-attribution rules for equipment foundations, secondary grouting, and vibration-isolation devices: BOQ caliber vs quota caliber
Equipment concrete foundations belong to civil works and are priced separately; the installation work content already includes base channel steel (GB/T 50856-2024 Clause 3.0.10), listed separately per kg under Appendix N only with special design. Secondary grouting is already included in the equipment installation work content at the BOQ level (Clause 3.0.9) and not listed separately, but some quota items exclude grouting, requiring a grouting item applied and merged into the all-in unit rate. Vibration-isolation devices are listed with equipment installation — installation included, main materials counted separately.
- ←
Measurement caliber for drainage pipes and rainwater-inlet connectors: computed by design centerline length (to centers, no deduction of auxiliary structures), contrasted with "manhole-deducting" local calibers and with workmanship provisions
Under the current national standard (GB/T 50857-2024) and Beijing (DB11/T 2382-2024), drainage pipes and inlet connectors are computed by design centerline length, without deducting the lengths occupied by rainwater inlets, manholes, and other auxiliary structures — measured to centers; there is no "measure to inner face (edge) then deduct" method; only under "manhole-deducting" calibers such as Shenzhen SJG 181.4-2024 is the length "manhole-center to manhole-center minus the per-manhole tabulated deduction", and even there the datum is center-to-center with tabulated values, not edge measurement. The workmanship rule "pipe end flush with inlet inner wall" is an installation requirement, not a takeoff datum.
- ←
Reserve rules for cables passing manholes and reserve (surplus) lengths for power / railway signal / urban rail signal / communication cables
Cables reserve at manholes: communication-duct manholes 1-2 m per end (max 3 m, GB 51158-2015 Clause 7.3.6); urban rail signal: 2 m in cable manholes, 2 m per end for entry/exit and termination, 3 m per terminal (DB11/T 2382-2024 Table 10.4.1); railway signal: 2 m per end for duct exit and termination, 2 m per splice, bending factor >= 2% (TB 10007-2017 Clause 17.0.11). Reserve (additional) length is a component of cable-laying quantity, not loss; design provisions govern, otherwise the standard reserve tables apply (GB 50217-2018 Clause 5.1.17).
- ←
Difference between grounding electrodes and grounding busbars, and their BOQ listing, measurement, and pricing calibers (GB/T 50856-2024 lightning protection and grounding devices, Table D.10.1)
The grounding electrode is the current-dispersing element, measured by design quantity in "pieces (blocks, sets)"; the grounding busbar is the connecting conductor, measured in "m" by total design length plus reserve (additional) length — separate items with different units, not interchangeable in pricing. Additional lengths of busbars, down-conductors, and lightning networks per Table D.17.3-6; TB/T 10829-2024 (per 10 m) and SJG 181.7-2024 (per linear meter) both add 3.9% to design length (turns, undulations, obstacle avoidance, splices).
- ←
Whether pipe-trench backfill quantities deduct the pipe volume: the 500 mm diameter demarcation rule and comparison of standards' calibers
Whether trench backfill deducts the pipe volume is demarcated at (nominal) diameter / pipe structural width 500 mm in most systems: <=500 mm no deduction; >500 mm deduct per the quota appendix table (m3/m) or the actual volume of pipe and base/cushion, with some systems (Shenzhen) also including chambers and other auxiliary structures; Hunan 2025 requires deducting the full pipe volume when backfilled with purchased sand/gravel; Beijing DB11/T 2382-2024 municipal/landscape caliber is "minus pipes and structures" with no 500 mm exemption. The text of the standard volume adopted governs.
- ←
Beijing DB11/T 2382-2024 consumption standard: rules for determining whether pipe installation quota line items include pipe fittings - in the gas chapter only galvanized steel pipe (threaded joints) items include fittings and pipe clamps while fittings of other materials are billed separately; pipe items of the water supply/drainage and heating chapters include fitting installation
Under DB11/T 2382-2024 clauses 6.10.32/6.10.34: pipe line items for indoor water supply, drainage and heating "shall include the fitting installation content" (fitting material quantities taken as the design-shown quantities or per Table 6.10.32), so no separate fitting-installation item may be applied; for gas piping, only galvanized steel pipe (threaded joints) items include fittings and pipe clamps, while for other materials (welded steel pipe, PE pipe, steel-skeleton plastic composite pipe etc.) the fittings and clamps must follow the corresponding "fitting and pipe-clamp installation" items. Pipes are measured along the design-shown centreline length with no deduction for lengths occupied by fittings and valves (6.10.36); fittings are counted as the design-shown number of pieces (6.10.37) - in gas works "pipe (m)" and "fittings (piece)" are two independent billed items.
- ←
Charging rules for pipeline pressure testing, flushing, disinfection, and water-quality testing costs (included in BOQ items vs. separately billed under quota norms vs. borne by the employer)
BOQ basis: GB/T 50856-2024 Table K.1.1 note 9 — the work content of all pipeline items includes pressure testing and purging/cleaning, so pressure testing/flushing are not billed separately; municipal quota norms (e.g., SJG 181.4-2024) exclude functional testing and disinfection flushing from pipeline laying, so dedicated quota line items must be applied; the water-quality testing fee is a statutory delivery inspection borne by the employer and is not within installation quota norms.
- ←
TB/T 10832-2024 railway budget quota Volume 11 water supply and drainage: scope and application rules (with the Chapter 1 water-source special calibers and 2024 revisions)
TB/T 10832-2024 Volume 11 (replacing TZJ 2011-2017, effective 1 January 2025) applies to new and rebuilt railway water supply, drainage, and noise-barrier works — the consumption standard for design estimates (budgets); unpriced materials are booked per design specs; pipe anti-corrosion and insulation may borrow Volume 12 TB/T 10833-2024 items. General rules: bracketed materials / HT-0 concrete / equipment costs not included — book separately; main materials may be swapped with consumptions unchanged; labor/material/plant prices per TB 10811-2024, TB/T 10813-2024, TB/T 10814-2024. Chapter 1 water sources: drilled wells apply by three strata (sand-clay / hard clay-sand-gravel / cobble-shale-slate) in segments; drilling diameter = casing diameter + filter thickness; well screens swapped per design; the well items exclude underground/overhead obstruction treatment.
- ←
Quantity take-off (measurement) and pricing rules for pipeline supports/hangers and seismic braces (GB/T 50856-2024 listing + GB 50981-2014 installation)
The fabrication, installation, and painting of ordinary pipeline supports, hangers, and base channel steel are already included in the work content of pipeline installation items (GB/T 50856-2024 Clause 3.0.10) and are generally not listed separately; where there are special design requirements they are listed under Appendix N (031301) — prefabricated supports per set, supports/hangers and base channel steel per kg. Seismic braces must be listed separately under the prefabricated-support item code, counted per set, with installation quantities per GB 50981-2014 Chapter 8: transverse braces at both ends of each horizontal straight pipe segment and at least one longitudinal, transverse braces within 0.6 m at bends, spacing l = l0·αEk·k (half for renovation works).
- ←
Ventilation duct quantity calculation and classified measurement: whether supply / exhaust / fresh-air ducts are computed separately, the developed (unfolded) area rules, BOQ listing, and quota-norm tiering basis
Ducts are computed from design dimensions as developed (unfolded) area (m2): no deduction is made for inspection ports, measuring ports, supply openings or suction openings; length is taken along the design centreline (main and branch ducts divided at their centreline intersections), including the length of elbows, tees, reducers and rectangular-to-round adapters, but excluding the length occupied by components. Supply, exhaust and fresh-air systems are governed by one and the same rule set — there are no per-system differences in the calculation method; "separation" is expressed at the BOQ listing and rate build-up levels — listed by item description (use/name, material, shape, size, plate thickness, joint form), and split when quota line items are applied according to tiering factors such as joint form and size; the system itself is not a tiering factor.
- ←
Applying quota items to socket solvent-cement jointing of UPVC water and drainage pipes under Beijing DB11/T 2382-2024, and judging the fittings content: take the "(solvent cement)" series, never the fusion series; match indoor / outdoor tables and diameter bands; fittings take no separate installation item; material quantities per the design-shown numbers or the fittings reference tables
UPVC socket solvent-cement jointing takes the "(solvent cement)" series items (indoor water supply table C.10.15-1, indoor drainage table C.10.17-1, outdoor water supply table C.10.4-2, outdoor drainage table C.10.5-2) and must not take the "fusion connection" series; the pipe items' work content already includes fitting installation, fittings take no separate installation item, and fitting material quantities are computed per the design-shown numbers or per the fittings reference tables 6.10.32 (indoor) / 6.10.23 (outdoor); pipe quantities are computed by length on the design-shown pipe centreline, without deducting the lengths fittings occupy.
- ←
Quota item selection for trenchless horizontal directional drilling (directional drilling / pipe pulling): process split, diameter banding, measurement rules and multi-pipe single-bore diameter determination
Trenchless directional drilling corresponds to "horizontal directional drilling": there is no all-in item; the three processes - pilot boring, reaming and pipe pull-back - are set as separate items and banded separately (Beijing DB11/T 2382-2024 items D4-11-152 to D4-11-166: pilot boring in three bands, reaming and pipe pull-back in six bands each). Measurement: pilot boring and reaming by the horizontal length between the two working pits; pipe pull-back by the pilot-bore length plus 1.5m. Where several pipes are pulled into one bore, the bore, reaming and pull-back diameters are determined by the smallest circumscribed circle of the pipe bundle. "Within" includes the stated figure; "beyond" excludes it.